Renesas Emulation Pod for M30240 Group MCUs M30240T-RPD-E Technické informace

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

( 8 / 58 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo

( 9 / 58 )IMPORTANTNote on Malfunctions in the PC4701 System• If the emulator malfunctions because of interference like external noise, do the followi

( 10 / 58 )IMPORTANTNotes on Downloading Firmware:• Before using this product for the first time, it is necessary to download the dedicated firmware(c

( 11 / 58 )IMPORTANTNotes on Stack Area:• With this product, a maximum 8 bytes of the user stack is consumed as a work area.• If the user stack does n

( 12 / 58 )IMPORTANTNotes on Address Match Interrupt:• Do not set software breaks at the same addresses as address-match interrupts as the program may

( 13 / 58 )IMPORTANTNote on Differences between Actual MCU and Emulator:•Operations of the emulator differs from those of actual MCUs as listed below.

( 14 / 58 )MEMO

( 15 / 58 )Chapter 2. PreparationThis chapter describes the package components, the system configuration and the preparation for using this product fo

( 16 / 58 )Chapter 2. Preparation2.1 TerminologySome specific words used in this user's manual are defined as follows:Emulator systemThis means a

( 17 / 58 )2.2 Package ComponentsThe M30240T-RPD-E package consists of the following items. When unpacking, check to see if yourpackage contains all o

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

( 18 / 58 )2.4 Name of Each Part(1) System ConfigurationFigure 2.1 System configuration(1) to (4) in Figure 2.1 are included with this product package

( 19 / 58 )(2) Inside of Emulation PodFigure 2.2 Internal view of emulation podHere following explains each board in Figure 2.2.(1) Common board (M302

( 20 / 58 )2.5 When Using the Emulator for the First TimeIf you have purchased this emulation pod newly, it is necessary to download the firmware. The

( 21 / 58 )Chapter 3. Setting UpThis chapter describes switch settings required for using this product and how to connect this product to the PC4701 a

( 22 / 58 )Chapter 3. Setting UpTo use this emulation pod with your target system, it is necessary to set as follows. Set the followingafter removing

( 23 / 58 )3.2 Switch SettingsFigure 3.2 shows the positions of switches and Table 3.1 lists the settings.Figure 3.2 Positions of switchesCAUTIONNote

( 24 / 58 )Table 3.1 Switch settings of M30240T-RPD-ESignal Switch Setting DescriptionConnects the LPF pin to the LPF circuit in the pod.JP1TLPF BLPFJ

( 25 / 58 )3.3 Selecting Clock SupplyThere are two ways to supply a clock to the MCU, using the oscillator circuit of the emulation podor using the os

( 26 / 58 )(1) Using the Oscillator Circuit on the Target SystemWhen turning on the power supply, the internal clock of emulation pod is selected to s

( 27 / 58 )(2) Changing the Internal Oscillator Circuit of Emulation PodAn oscillator circuit board for 12MHz is mounted on this product. To use the e

M30240T-RPD-EUser’s ManualUser’s ManualRev.1.00 2003.09Emulation Pod for M30240 Group MCUs

( 28 / 58 )(3) Replacing the Oscillator Circuit BoardsFigure 3.7 shows how to replace the oscillator circuit boards. For the position of the oscillato

( 29 / 58 )3.4 A-D Conversion Bypass CapacitorThis product has foot patterns on the board for mounting a bypass capacitor. Mount a suitable bypasscapa

( 30 / 58 )3.5 Connecting the PC4701 and Emulation PodTo connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable includedwi

( 31 / 58 )(2) Connecting the Cable to the Emulation PodFigure 3.10 shows how to connect the FLX120-RPD and the emulation pod.Figure 3.10 Connecting F

( 32 / 58 )3.6 Connecting the Target System(1) How to Connect the Target SystemFigure 3.11 shows how to connect this product and the target system.CAU

( 33 / 58 )(2) Connecting 80-pin LCC SocketWhen connecting the emulation pod to the 80-pin LCC socket (IC61-080-079, IC61-080-081, IC61-0804-046 made

( 34 / 58 )3.7 Modifying the MCU File for M3T-PD30It is necessary to change the contents of the MCU file depending on the MCU being developed. Forthe

( 35 / 58 )Chapter 4. UsageThis chapter describes from turning on the power of this product to starting up the emulator debugger.4.1 Turning On the Po

( 36 / 58 )Chapter 4. Usage4.1 Turning On the Power(1) Checking the Connection of the Emulator SystemBefore turning the power ON, check the connection

( 37 / 58 )(3) LED Display When PC4701 Starts Up NormallyAfter the emulator starts up, check the status of the LEDs on the front panel to see whether

( 2 / 58 )• IC61-080-079, IC61-080-081 and IC61-0804-046 are products of Yamaichi Electronics Co., Ltd.Keep safety first in your circuit designs!• Ren

( 38 / 58 )4.2 Downloading Firmware(1) When It is Necessary to Download FirmwareIt is necessary to download firmware when:(1) you use this product for

( 39 / 58 )4.3 Self-checks(1) Self-check ProcedureTo run the emulator self-checks, do so as explained here below. While self-checks are in progress,LE

( 40 / 58 )Figure 4.4 Self-check procedure

( 41 / 58 )Chapter 5. SpecificationsThis chapter describes specifications of this product.5.1 Specifications ...

( 42 / 58 )Chapter 5. Specifications5.1 SpecificationsTable 5.1 lists the specifications of M30240T-RPD-E.Table 5.1 Specifications of M30240T-RPD-EPC4

( 43 / 58 )Figure 5.1 Connection diagram5.2 Connection Diagram(1) Connection Diagram of M30240T-RPD-EFigures 5.1 shows the connection diagram of M3024

( 44 / 58 )Figure 5.2 External dimensions of emulation pod5.3 External Dimensions(1) External Dimensions of Emulation PodUnit: mm

( 45 / 58 )Figure 5.3 External dimensions of pitch converter board (FLX-80LCC)(2) External Dimensions of Pitch Converter Board (FLX-80LCC)Figure 5.3 s

( 46 / 58 )MEMO

( 47 / 58 )Chapter 6. TroubleshootingThis chapter describes how to troubleshoot when this product does not work properly.6.1 Flowchart to Remedy the T

( 3 / 58 )PrefaceThe M30240T-RPD-E is an emulation pod for the M30240 Group of 16-bit microcomputers. It's usedwith a PC4701 emulator.This user&a

( 48 / 58 )Chapter 6. Troubleshooting6.1 Flowchart to Remedy the TroublesFigure 6.1 shows the flowchart to remedy the troubles from when power to the

( 49 / 58 )6.2 When the Emulator Debugger Does Not Start Up Properly(1) When the LED Display of PC4701 is AbnormalTable 6.1 LED's abnormal displa

( 50 / 58 )(2) Errors Occur When the Emulator Debugger Starts Up(When the target system is connected)Table 6.2 Checkpoints of errors when starting up

( 51 / 58 )(3) Errors Occur When the Emulator Debugger Starts Up(When the target system is not connected)Table 6.3 Checkpoints of errors when starting

( 52 / 58 )MEMO

( 53 / 58 )Chapter 7. Maintenance and GuaranteeThis chapter describes how to maintenance, repair provisions and how to request for repair.7.1 Maintena

( 54 / 58 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 55 / 58 )7.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

( 56 / 58 )MEMO

M30240T-RPD-E User's ManualRev.1.00September 1, 2003REJ10J0262-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATI

( 4 / 58 )ContentsChapter 1. Precautions for Safety ...71.1 Sa

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanM30240T-RPD-EREJ10J0262-0100ZUser’s Manual

( 5 / 58 )Chapter 5. Specifications ...415.1 Specif

( 6 / 58 )MEMO

( 7 / 58 )Chapter 1. Precautions for SafetyThis chapter describes precautions for using this product safely and properly. For precautions for the emul