Renesas H8S/2378F Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě Renesas H8S/2378F. Renesas H8S/2378F Product data Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Flash Development Toolkit

REJ06J0002-0100 Application Note (Introduction)Flash Development ToolkitRev.1.00 Jun. 28, 2006

Strany 2

2.3 Simple Interface Mode The simple interface mode allows you to manage multiple devices, programs, or data by creating a project, and registering a

Strany 3 - Revision 1.0

3. Operating the H8/300H Tiny Series (H8/3694F) 3.1 Connecting the H8/3694F and Adapter Board 3.1.1 Connecting the Adapter Board On-board programmi

Strany 4 - Contents

3.1.2 User Interface Cable Signals Pin numbers and corresponding signals of the user system interface cable used for connecting the adapter board and

Strany 5

H8/3694FTxDRxD3RES15Vcc1751VIN(Vcc)RXDTXDMD0RESGND2,4,6,8,10,12,14,16Adapter board(HS0008EAUF1H)Pulled up at 47 kΩor more.Pulled up atabout 1 kΩ.Note:

Strany 6

3.1.4 Setting Pins on the Adapter Board An example of setting pins for the boot mode when the H8/3694F user system and Renesas adapter board (HS0008E

Strany 7 - 1. Overview

3.2 Boot Mode The following two modes are available to program and erase flash memory: The boot mode which enables on-board programming/erase operatio

Strany 8

3.3 Starting the Flash Development Toolkit From the "All Programs" menu, select "Flash Development Toolkit 3.4 Basic." The basic

Strany 9

3.4 Setting Product Information 3.4.1 New Settings Select "New Settings" from "Options." The screen for selecting the device and

Strany 10 - 2.3 Simple Interface Mode

3.4.2 Selecting the Device and Kernel Select the target device from the pull-down menu. In this example, select H8/3694F. When you have selected th

Strany 11

3.4.3 Selecting a Communications Port Select the adapter board (FDM) from the pull-down menu. When you have selected the communications port, click

Strany 12

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. R

Strany 13

3.4.4 Device Settings (Setting the Input Clock) Enter the frequency of the clock used for the board in MHz. For example, enter 9.8 (MHz). When you

Strany 14

3.4.5 Selecting the Connection Type (Boot Mode and Communication Speed) Select "BOOT Mode" for "Select Connection." Set the baud

Strany 15 - 3.2 Boot Mode

3.4.6 Selecting Programming Options (Protection Level and Messaging Level) Select the protection level and messaging level. For example, select "

Strany 16

3.4.7 Adapter Board Pin Settings Set the pins on the adapter board (FDM) for the boot mode. In the H8/3694F boot mode, set the output of P85 to high

Strany 17 - 3.4.1 New Settings

An example of connecting the H8/3694F and Renesas adapter board (HS0008EAUF1H) is shown in Figure 3-3. The pull-up and pull-down resistor values shown

Strany 18

3.4.8 Reset Mode Pin Settings Set pins on the adapter board for restarting the device in the reset mode. These settings are not required for this pro

Strany 19

3.4.9 Completion of Setting Device and port settings are now completed. 20

Strany 20

3.5 Programming Flash Memory 3.5.1 Selecting the Program Area and File Select the download program area and the S-type file. Check "User Area&q

Strany 21

3.5.2 Starting Programming File selection has been completed. When the Flash Development Toolkit is started up for the second and subsequent times, th

Strany 22

3.5.3 Selecting a USB Device Select a USB device. In this example, select the adapter board (FDM). When you have selected the USB device, click &q

Strany 23

Renesas Flash Development Toolkit Application Note (Introduction) Revision 1.0 Renesas Technology Corp.

Strany 24

3.5.4 Ending Programming Programming starts, then ends. Confirm the message indicating that programming terminated normally. Click "Exit."

Strany 25

3.6 Reprogramming To program flash memory for the second and subsequent times in the basic simple interface mode, follow the procedure below: Open &qu

Strany 26 - 3.4.9 Completion of Setting

4. Operating the H8S Family (H8S/2378F) 4.1 Connecting the Adapter Board The on-board programming adapter board for F-ZTAT* microcomputers HS0008EAU

Strany 27

A list of pin numbers and corresponding signals of the user system interface cable used for connecting the adapter board and user system is shown belo

Strany 28

H8S/2378FTxD1RxD1MD0MD1RES15Vcc171VIN(Vcc)RXDTXDRESGND2,4,6,8,10,12,14,16Adapter board(HS0008EAUF1H)Pulled up at 47 kΩ or morePulled up at about 1 kΩ.

Strany 29

4.1.2 Setting Pins on the Adapter Board An example of setting pins for the boot mode when the H8S/2378F user system and Renesas adapter board (HS0008

Strany 30

4.2 Boot Mode 4.2.1 Operating Modes The H8S/2378 has six operating modes (modes 1 to 5 and 7). The operating mode is selected by the setting of mode p

Strany 31 - 3.6 Reprogramming

The results of comparing programming and erasing related functions on the boot mode, user program mode, and user boot mode are shown in Table 4-4. Tab

Strany 32

4.3 Activating the Flash Development Toolkit From the "All Programs" menu, select "Flash Development Toolkit 3.4 Basic." The bas

Strany 33

4.4 Setting Product Information 4.4.1 New Settings Select "New Settings" from "Options." The screen for selecting the device and

Strany 34

Contents 1. Overview ...1 2. Functi

Strany 35

4.4.2 Selecting the Device and Kernel Select the target device from the pull-down menu. Select "Generic BOOT Device" because the H8S/2378

Strany 36 - 4.2 Boot Mode

4.4.3 Selecting a Communications Port Select the adapter board (FDM) from the pull-down menu. When you have selected the communications port, clic

Strany 37

4.4.4 Adapter Board Pin Settings Set the pins on the adapter board (FDM) for the boot mode. For example, set the output of FWx to high (1) and that o

Strany 38

An example of connecting the H8S/2378F and Renesas adapter board (HS0008EAUF1H) is shown in Figure 4-3. The pull-up and pull-down resistor values show

Strany 39 - 4.4.1 New Settings

4.4.5 Selecting the USB Device Check the device. Select the adapter board (FDM). When you have selected USB device, click "OK." 38

Strany 40

4.4.6 Selecting the Device Check the device. Select HD64F2378. When you have selected the device, click "OK." 39

Strany 41

4.4.7 Selecting the Clock Mode Check the device. Select the clock mode. When you have selected the clock mode, click "OK." 40

Strany 42

4.4.8 Checking the Generic Device The device has been checked. Click "OK." 41

Strany 43

4.4.9 Setting the Device (Input Clock) In the first column enter the frequency of the clock used for the board in MHz. For example, enter 8.25 (MHz).

Strany 44

4.4.10 Selecting the Connection Type (Communication Speed) Select a baud rate from the pull-down menu. For example, select 19200 (baud). When you

Strany 45

4.2.1 Operating Modes ... 30 4.

Strany 46

4.4.11 Selecting Programming Options (Protection Level and Messaging Level) Select the protection level and messaging level. For example, select &quo

Strany 47

4.4.12 Reset Mode Pin Settings (FDM) Set pins on the adapter board (FDM) for restarting the device in the reset mode. These settings are not required

Strany 48

4.4.13 Completion of Setting Device and port settings are now completed. 46

Strany 49

4.5 Programming Flash Memory 4.5.1 Selecting the Program Area and File Select the download program area and S-type file. Check "User Area"

Strany 50

4.5.2 Starting Programming File selection has been completed. When the Flash Development Toolkit is started up for the second and subsequent times, th

Strany 51

4.5.3 Ending Programming By clicking "Start", programming starts, then ends. Confirm the message indicating that programming terminated norm

Strany 52

4.6 Reprogramming To program flash memory for the second and subsequent times in the basic simple interface mode, follow the procedure below: Open &qu

Strany 53

5. Operating the R8C/Tiny Series (R5F21154) The single-chip microcomputer R8C/15 Group incorporates flash memory. This section describes how to progr

Strany 54

5.3 Starting the Flash Development Toolkit From the "All Programs" menu, select "Flash Development Toolkit 3.4 Basic." The basi

Strany 55

5.4 Setting Product Information 5.4.1 New Settings Select "New Settings" from "Options." The screen for selecting the device and

Strany 56 - 4.6 Reprogramming

5.5.4 Ending Programming... 62 5.6 Re

Strany 57 - Host computer

5.4.2 Selecting the Device and Kernel Select the target device from the pull-down menu. In this example, select R5F21154. When you have selected

Strany 58

5.4.3 Selecting the Communications Port Select E8 from the pull-down menu. When you have selected the communications port, click "Next(N).&quo

Strany 59

5.4.4 Selecting the Connection Type (Communication Speed) Set the baud rate. For example, select "Use Default." When you have selected th

Strany 60

5.4.5 Selecting Programming Options (Protection Level and Messaging Level) Select the protection level and messaging level. For example, select "

Strany 61

5.4.6 Completion of Setting Device and port settings are now completed. 58

Strany 62

5.5 Programming Flash Memory 5.5.1 Selecting the Program Area and File Select a download program area and S type file. Check "User Area" i

Strany 63

5.5.2 Starting Programming When the Flash Development Toolkit is started up for the second and subsequent times, the following screen is opened. The

Strany 64 - 5.4.6 Completion of Setting

5.5.3 Setting the Power Supply Set the power supply. Check "Power Supply" and set the power supply voltage to 5.0 V. When you have set

Strany 65

5.5.4 Ending Programming Click "Start." Programming starts, then ends. Confirm the message indicating that programming terminated normally.

Strany 66

5.6 Reprogramming To program flash memory for the second and subsequent times in the basic simple interface mode, follow the procedure below: Open &qu

Strany 67

1. Overview This application note describes how to use the Renesas Flash Development Toolkit. The target devices are the following three series: (1)

Strany 68

5.7 ID Code 5.7.1 ID Code Checking Function In the standard serial input/output mode, the ID code checking function is available to prevent flash mem

Strany 69 - 5.6 Reprogramming

A new file is programmed. 65

Strany 70 - 5.7 ID Code

5.7.4 ID Code Mismatch If the entered ID code differs from the programmed ID code, an ID code mismatch occurs and no file can be programmed. 66

Strany 71 - A new file is programmed

5.7.5 ID Code File When an ID code is set, an id file is created. This id file contains the set ID code. You can use this file to set an ID code. W

Strany 72

A new file is programmed. 68

Strany 73

6. Selecting and Setting Functions This section describes how to select a function and set the selected function. 6.1 Options Menu 6.1.1 Login... Th

Strany 74

Area. For devices with a Data Area, the user can choose whether to download the file to the User Area or the Data Area. 6.2.4 Program Flash Clicking o

Strany 75 - 6.2 Dialog Control

Flash Development Toolkit Application Note (Introduction) Publication Date: Jun. 28, 2006 Rev.1.00 Published by:

Strany 76

Flash Development Toolkit Application Note (Introduction)

Strany 77

The graphical user interface screen of the Flash Development Toolkit is shown in Figure 2-1. Figure 2-1 Graphical User Interface of the Flash Deve

Strany 78

2.2 Basic Simple Interface Mode The basic simple interface mode allows you to easily write a program or data in flash memory on the target device wit

Komentáře k této Příručce

Žádné komentáře