Renesas M16C/6NK Uživatelský manuál Strana 1

REG10J0017-0100 Renesas Starter KitRSKM16C6NK User’s Manual RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY Rev.01.00 R

6.4. Serial port The microcontroller programming serial port 1 is connected to the E8 connector. A serial port can be used by moving option resistors

6.5. LCD Module An LCD module is supplied to be connected to the connector J11. This should be fitted so that the LCD module lies over J3. Care shou

6.6. Option Links Table 6-6 below describes the function of the option links contained on this RSK board. Option Link Settings Reference Function F

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R100 External Oscillator Connects External Ring header pins to Mi

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R109 VREF Connects Board VCC1 supply to VREF VREF can be provided

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R85 Microcontroller pin function select Connects microcontroller

6.7. Oscillator Sources A crystal oscillator is fitted on the RSK and used to supply the main clock input to the Renesas microcontroller. Table 6-7 d

Chapter 7. Modes The RSK supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the M16C/6NK Group Hardwa

Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E8 debugger. Refer to the M16C/6NK Group Hardware Manual for

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller

Table of Contents Chapter 1. Preface...

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 A19_LED3 49 2 A18_LED2 50 3 A17_LED1 51 2 A16_LED0 52 5 A15_IO7 53

9.2. Application Headers Table 9-5 and Table 9-6 below show the standard application connections. * Marked pins are subject to option links. JA1 Pin

Table 9-7 to Table 9-9 below show the optional generic header connections. * Marked pins are subject to option links. JA3 Pin Header Name RSK Sign

JA5 Pin Header Name RSK Signal Name Device Pin Pin Header Name RSK Signal Name Device Pin 1 ADC4 I4 AN4* 90 2 ADC5 I5 AN5* 89 3 ADC6 I6

Table 9-10 below shows the CAN connections J14 Pin Function Signal Name Device Pin 1 CAN0 Positive CAN0H 21 2 GROUND 3 CAN0 Negative CAN0

Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the RSK board must be connected to a PC USB p

10.4. Memory Map SFRReserved areaExternal AreaInternal RAMH'00400H'07FFFH'0F000H'00000H'28000Program RAM

Chapter 11.Component Placement Figure 11-1: Component Placement 25

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW, refer to the HEW manual available on the CD or

Renesas Starter Kit for M16C/6NK User's Manual Publication Date Rev.01.00 28.06.2006 Published by: Renesas Technolog

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this d

Renesas Starter Kit for M16C/6NK User's Manual Renesas Technology Europe Ltd. Duke’s Meadow, Millboard Road,

Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User C

Chapter 3. Power Supply 3.1. Requirements This RSK operates from a 5V power supply. A diode provides reverse polarity protection only if a current l

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. Figure 4-1: Board Layout

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid

Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. MicrocontrollerUser: 4 LEDS1Green, 1Oran

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the RSK. The function of each switch and its connection are shown in Tabl