Renesas H8S2215R Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Generátory energie Renesas H8S2215R. Renesas Starter Kit for H8S/2215R Tutorial Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 26
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
REG10J0023-0100
Renesas Starter Kit
RSK H8S2215R Tutorial Manual
RENESAS SINGLE-CHIP MICROCOMPUTER
Rev.1.00 Renesas Technology Europe Ltd.
Revision date 12.01.2007 www.renesas.com
Zobrazit stránku 0
1 2 3 4 5 6 ... 25 26

Shrnutí obsahu

Strany 1 - RSK H8S2215R Tutorial Manual

REG10J0023-0100 Renesas Starter KitRSK H8S2215R Tutorial Manual RENESAS SINGLE-CHIP MICROCOMPUTER Rev.1.00 Rene

Strany 2 - Table of Contents

• Select the Device on the RSK from the drop down list. • In the sub pane, select the kernel version that ends in ‘.RSK’. • Press <Next>. If

Strany 3 - Chapter 1. Preface

• Ensure that ‘USER Program Mode’ is selected. • Confirm that ‘Use Default’ is selected. • Press <Next>. • Confirm the default selection

Strany 4 - Chapter 2. Introduction

Damage to the microcontroller can be sustained with incorrect settings. • Confirm the mode pin settings. • Press <Next>. • The following

Strany 5

5.3.1. Connecting To HMon We can now attempt to connect to the target device. • Press the Green ‘Connect’ Icon. HMon is able to discover the inter

Strany 6 - 4.1. Introduction

• Confirm the settings shown and press <OK>. HMon will attempt to connect to the RSK. If it succeeds then the Output window in HEW will show

Strany 7 - 4.3.1. Build Configuration

• Ensure ‘0x000D – 1 [Closed]’ is selected and click <OK>. On completion of the download HMon will automatically re-connect to the monitor an

Strany 8 - 5.1. Building Code

Chapter 6. Downloading and Running the Tutorial Once the code has been built in HEW it needs to be downloaded to the RSK. Now that you are connected

Strany 9

We will now skip over the initialisation code and proceed to the main tutorial. • Open the file called ‘resetprg.c’ by double clicking it in the pr

Strany 10

• Right click on the ‘FlashLEDs();’ function and select ‘Go to cursor’. The code will run to the selected line and stop. A temporary breakpoint was

Strany 11

The code will now run to the infinite loop at the end of Main(). The user LEDs should now be flashing. You can modify the flashing rate by adjusting

Strany 12

Table of Contents Chapter 1. Preface...

Strany 13 - 5.3.1. Connecting To HMon

• Press ‘Go’ to run the code from the current PC position. When the program stops you can see the modified string displayed on the second line of t

Strany 14

Chapter 7. Project Files 7.1. Standard Project Files The RSK tutorials are configured so that it is possible to provide the same tutorial code on m

Strany 15

7.1.2. Board initialisation code (Hwsetup.c / hwsetup.h) There are four common stages to the configuration of the microcontroller device. The code to

Strany 16

7.1.3. Main Tutorial Code (main.c / main.h) The main tutorial code is common to all tutorial projects. The display initialisation and string display

Strany 17

Chapter 8. Additional Information For details on how to use High-performance Embedded Workshop (HEW), refer to the HEW User manual available on the

Strany 18

Renesas Starter Kit for H8S2215R Tutorial Manual Publication Date Rev.1.00 12.01.2007 Published by: Renesas Techno

Strany 19

Renesas Starter Kit for H8S2215R Tutorial Manual Renesas Technology Europe Ltd.Dukes Meadow, Millboard Road, Bou

Strany 20

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. No one is permitted t

Strany 21 - Chapter 7. Project Files

Chapter 2. Introduction This manual is designed to answer, in tutorial form, the most common questions asked about using a Renesas Starter Kit (RSK)

Strany 22

Chapter 3. Tutorial Project Workspace The workspace includes all of the files for two build configurations. The tutorial code is common to both the

Strany 23

Chapter 4. Project Workspace 4.1. Introduction HEW is an integrated development tool that allows the user to write, compile, program and debug a sof

Strany 24

• Click OK to start the RSK Project Generator wizard. The next dialog presents the example projects available. Choose the Tutorial code which will b

Strany 25

Chapter 5. Building the Tutorial Project The tutorial project build settings have been pre-configured in the tool-chain options. To view the tool ch

Strany 26 - Tutorial Manual

5.2. Connecting the debugger For this tutorial it is not necessary to provide an external power supply to the board, the power will be provided by t

Komentáře k této Příručce

Žádné komentáře