Renesas SuperH SH7700 Series Uživatelský manuál Strana 1

2003.12.3SuperH Family E10A EmulatorAdditional Document for User’s ManualSH7729R E10A HS7729RKCM02HERenesas Microcomputer Development Environment Sys

6Pin No. SignalInput/OutputFP-208 Note NoteBP-240/AUDSYNCNCNCNCTCKGNDAU DATA 0GNDAU DATA 1GNDGNDGNDGNDGNDGNDGNDAU DATA 2AU DATA 3NCTMS/RESETPGNDAUDCKG

7Pin 1 markPin No. SignalSH7729R, SH7709S Pin No.12*34*567*118 to 1012 to 1314*TCK/TRSTTDO/ASEBRKAK TMSTDI/RESETPNot connectedGNDInput/Output*InputInp

81.5 Recommended Circuit between the H-UDI Port Connector and theMPU1.5.1 Recommended Circuit (36-Pin Type)Figure 1.4 shows a recommended circuit for

91AUDATA0AUDATA2AUDATA1AUDATA3TCKTMSN.C.N.C.N.C.TDITDOAUDCKN.C.GNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGND357911131517192123252729313335

101.5.2 Recommended Circuit (14-Pin Type)Figure 1.5 shows a recommended circuit for connection between the H-UDI port connector (14pins) and the MPU.N

11Section 2 Specifications of the SH7729R E10A Emulator’sSoftware2.1 Differences between the SH7729R, SH7709S, and the Emulator1. When the emulator

123. Low-Power States (Sleep, Software Standby, and Module Standby)For low-power consumption, the SH7729R and SH7709S have sleep, software standby, an

13When a one-byte memory is read from the command-line window, the stopping time will beabout 35 ms.7. Memory Access during User Program BreakThe emul

1410.UBCWhen [User] is specified in the [UBC mode] list box in the [Configuration] dialog box, theUBC can be used in the user program.Do not use the U

15• The internal I/O registers can be accessed from the [IO] window. However, note thefollowing when accessing the SDMR register of the bus-state con

CautionsKeep safety first in your circuit designs!1. Renesas Technology Corp. puts the maximum effort into making semiconductor productsbetter and mor

162.2.2 Break Condition FunctionsIn addition to BREAKPOINT functions, the emulator has Break Condition functions. Three typesof conditions can be set

17Table 2.6 lists the combinations of conditions that can be set under Break Condition 1, 2, 3.Table 2.6 Dialog Boxes for Setting Break ConditionsTy

182.2.3 Trace FunctionsTable 2.7 shows the trace functions.Table 2.7 Trace FunctionsFunction DescriptionInternal trace Branch instruction trace func

19Table 2.8 Type Name and AUD FunctionType Name AUD FunctionHS7729RKCM01H Not availableHS7729RKCM02H AvailableHS7729RKCI01H Not availableHS7729RKCI0

202.2.4 Notes on Using the JTAG Clock (TCK) and AUD Clock (AUDCK)1. When JTAG clock (TCK) is used, set the JTAG clock (TCK) frequency to lower than th

21according to the VP_MAP table. However, for addresses out of the range of the VP_MAPtable, the address to which a BREAKPOINT is set depends on the

224. If a PC break address condition is set to the slot instruction after a delayed branch instruction,user program execution cannot be terminated bef

SuperH Family E10A EmulatorAdditional Document for User's ManualSpecific Guide for the SH7729R E10A EmulatorPublication Date: Rev.1.00, Decemb

iContentsSection 1 Connecting the Emulator with the User System... 11.1 Components of the Emulator ...

ii

1Section 1 Connecting the Emulator with the User System1.1 Components of the EmulatorThe SH7729R E10A emulator supports the SH7729R and SH7709S. Ta

2Table 1.1 Components of the Emulator (HS7729RKCM01H, HS7729RKCM02H,HS7729RKCI01H, or HS7729RKCI02H)Classi-fication Component AppearanceQuan-tity Re

3For EMI countermeasure, use the ferrite core by connecting the user interface cable.When the user interface cable is connected with the emulator or u

41.2 Connecting the E10A Emulator with the User SystemTo connect the E10A emulator (hereinafter referred to as the emulator), the H-UDI port connector

51.3 Installing the H-UDI Port Connector on the User SystemTable 1.3 shows the recommended H-UDI port connectors for the emulator.Table 1.3 Recommen