C-7
REVISION HISTORY
Rev. Date Description
Page Summary
R8C/10 Group Hardware Manual
1.20
Jan.27.2006
113 14.7 Output Impedance of Sensor under A/D Conversion added
116 Figure 15.1 Programmable I/O Ports (1); NOTES: 1 added
117 Figure 15.2 Programmable I/O Ports (2); NOTES: 1 added
118 Figure 15.3 Programmable I/O Ports (3); NOTES: 1 added
119 Figure 15.4 Programmable I/O Ports (4); NOTES: 3 added
127
_______
Table 15.20 Port P33/INT3/TCIN Setting; Bit: “PD3_1” → “PD3_3”
_______
Table 15.22 Port P45/INT0 Setting; Bit: “PD3_3” → “PD4_5”
Table 15.23 Port X
IN/P46, XOUT/P47 Setting;
Setting value: External input to X
IN pin, “H” output from XOUT pin;
CM1: “1” → “0”, CM0: “0” → “1”, Feedback resistance: “OFF” → “ON”
129 Table 16.2 Recommended Operating Conditions; NOTES: 1, 2, 3 revised
130 Table 16.3 A/D Conversion Characteristics;
“A/D operation clock frequency” → “A/D operating clock frequency” revised
NOTES: 1, 2, 3, 4 revised
Table 16.4 Flash Memory (Program ROM) Electrical Characteristics;
“Data retention duration” → “Data hold time” revised
“Topr” → “Ambient temperature” revised
NOTES: 2 added
Measuring condition of byte program time and block erase time deleted
132 Table 16.6 Electrical Characteristics (1) [V
CC
=5V];
“P10 to P17 Except XOUT” → “Except P10 to P17, XOUT” revised
133 Table
16.7 Electrical Characteristics (2) [V
CC
=5V]
NOTES: 1, 2 revised
Measuring condition: Stop mode “Topr = 25 °C”
added
136 Table 16.13 Electrical Characteristics (3) [V
CC
=3V]
“P10 to P17 Except XOUT” → “Except P10 to P17, XOUT” revised
137 Table
16.14 Electrical Characteristics (4) [V
CC
=3V]
NOTES: 1, 2 revised
Measuring condition: Stop mode “Topr = 25 °C”
added
147 Figure 17.4 FMR1 and FMR4;
Flash memory control register 4 NOTES: 2 “Other than this period, this bit is set to
“0”.” revised
153 Figure 17.11 Block Erase Command (When Using Erase-suspend Function);
“Write ‘D0
16
’ to the uppermost block address”
→
“Write ‘D0
16
’ to the any block address” revised
156 Figure 17.12 Full Status Check and Handling Procedure for Each Error revised
158 Table 17.7 Pin Functions (Flash Memory Standard Serial I/O Mode);
____________
RESET: revised
162 19.1.1 Stop Mode
“Use the next program to enter stop mode.” added
“• Example of entering stop mode”
→
“• Program of entering stop mode”
“Program Example”
deleted
166 19.3.1 Oscillation Stop Detection Function
“Since the oscillation stop ... is 2 MHz or below, ...” →
“Since the oscillation stop ... is below 2 MHz, ...” revised
176
Appendix figure 2.2 Connecting examples with M16C Flash Starter (M3A-0806)
;
Pulled up added
NOTES: 1 revised
(120 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce